![]() In Wi-Fi client mode, you'll need to check the IP address displayed on the screen (toggle the network information display by pressing the settings button or the mode button). Simply choose "Open network stream" and type rtsp:// followed by the camera's IP address. On Android, you can use VLC Media Player, available in the Play Store. To view the stream, all you need is a video player capable of opening an RTSP stream. enjoy, Mtz You are faster than me, I received your msg while I am typing. Maybe just the top LED is not so visible. But with the original GitUp frame you can put the camera upside-down without any problem. The camera serves up a video feed via RTSP whenever it is connected to WiFi (client mode or AP mode). The Sony IMX206 CMOS sensor used by Git2 is not supporting image rotation. This flexible cord is great for eliminating mess and clutter for a clean. ![]() So this Gist aims to be an unofficial manual for the Git2, and it may be applicable to other GitUp cameras. This 10ft ReadyPlug cable is guaranteed to work with the GitUp Git2 Action Camera. I had to read 3 forum posts to even figure out how to connect it to a wifi network. I love my Git2P camera, but I am very disappointed in the unprofessional forum-style support available for even basic functions on the cameras. I decided I did not really want to mess with it any longer, because things seemed kind of flaky and unrealiable - but that was obviously just my experience - I gave up after how easy the gopro worked.Unofficial Manual for GitUp Git2/Git2P Action Cameras I did not end up liking my setup though, atleast not once I got my gopro, so I returned the Git2. They have the free designs cataloged and the websites software does all the 3D printing calculations automatically (even lets you know if the part will not print correctly) and you do not have to get into all the nitty gritty of 3D printing stuff. The parts turned out really well and I got um relatively cheap because I ordered several parts at the same time all with the same base specs (color, fill-ratio, etc.) so I was only charge one $10 setup fee (the parts themselves cost anywhere from $1.50 - $6 depending on what I was buying and how many I was ordering. ![]() The 3D printed parts are available and i purchased from "", their 3D Co-OP-like printing service. The stock solo gimbal HDMI connector works on this camera after you cut away a bit of the plastic underneath the connector - careful not to slice into the rubber covering the HDMI cable as I did, nearly slicing the wire, making my backup gimbal useless. The gimbal functions as smooth as it did with a GoPro. The fact that the Git2P weighs 23grams less than the GoPro Hero 4 Black helps. I was worried the gimbal would have a problem with the new camera sitting a quarter of an inch forward but it was not a problem. Then put the camera in the desired mounting position, aim it through the wiendshield to outside and check the screen, when the desired luminosity appears in the Git2 screen press the side button to lock those parameters and record with them (of course tigh the setup bolts in that moment). A small amount of trimming of plastic corner under the HDMI cable solved this problem. The HDMI cable was a couple of mm to short to plug into the camera. 4K modes replaced with 2K 24fps and 1080p30 (note that modes shown in UI are not changed). Bitrate values changed reaching 45Mbps for some modes. ![]() Velcro is simple and secure plus it makes it easy to change cameras. Hi, I modified the FW V1.6.1 for Git2 action camera. ![]() I use a Velcro strap to hold the camera in place. Then I carefully cut off the rounded tab, on the left side, that was used to hold a GoPro, but was now in the way. Since the GIT2P has to sit in front of the connector, I made a quarter inch thick pad for the camera to rest against (see photo), using the black dense foam that came with the gimbal. I did not want to remove it, because I still want to be able to use it with a GoPro. The first problem I had to deal with was the connector that plugs into the back of a GoPro. Use of this camera required some modifications to the SOLO gimbal, but I made sure that I can still use a GoPro if I want. ![]()
0 Comments
Leave a Reply. |